Software Implementation of Iris Recognition System using MATLAB

The software implementation of iris recognition system introduces in this paper. This system intends to apply for high security required areas. The demand on security is increasing greatly in these years and biometric recognition gradually becomes a hot field of research. Iris recognition is a branch of biometric recognition method. In thesis, Iris recognition system consists of localization of the iris region and generation of data set of iris images followed by iris pattern recognition. In thesis, a fast algorithm is proposed for the localization of the inner and outer boundaries of the iris region. Located iris is extracted from an eye image, and, after normalization and enhancement, it is represented by a data set. Using this data set a Neural Network NN is used for the classification of iris patterns. The adaptive learning strategy is applied for training of the NN. The implementation of the system is developed with MATLAB. The results of simulations illustrate the effectiveness of the neural system in personal identification. Finally, the accuracy of iris recognition system is tested and evaluated with different iris images. 

by Mo Mo Myint Wai | Nyan Phyo Aung | Lwin Lwin Htay "Software Implementation of Iris Recognition System using MATLAB" 

Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-5 , August 2019,

URL: https://www.ijtsrd.com/papers/ijtsrd25258.pdf

Paper URL: https://www.ijtsrd.com/engineering/electronics-and-communication-engineering/25258/software-implementation-of-iris-recognition-system-using-matlab/mo-mo-myint-wai

call for paper Industrial Engineering, international journal Nuclear Engineering, ugc approved journals for engineering

System Consideration, Design and Implementation of Point To Point Microwave Link for Internet Access

Microwave technology is extremely used for point to point communications because it is more easily focused into narrower beams than radio waves, allowing frequency use, it is available higher data transmission rates and antenna sizes are smaller than at lower frequencies. The main aim of this system is to provide internet access for rural area using ePMP Force 180 5GHz subscriber module. The two sites are 1.45 km away from each other. GPS is used to determine the latitude and longitude of two sites location. Google Earth Pro software is used to check for line of sight in choosing potential terminal site locations. In this system, system consideration, design and analysis of line of sight microwave link and hardware implementations are to be carried out. In the analysis, path profile, Fresnel zone, link budget and other parameters are implemented using the link planner software 

by Lay Nandar Soe | Kyaw Thet Zaw | Wai Phyo Aung "System Consideration, Design and Implementation of Point-To-Point Microwave Link for Internet Access"

Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-5, August 2019,

URL: https://www.ijtsrd.com/papers/ijtsrd26769.pdf 

Paper URL: https://www.ijtsrd.com/engineering/electronics-and-communication-engineering/26769/system-consideration-design-and-implementation-of-point-to-point-microwave-link-for-internet-access/lay-nandar-soe

call for paper Chemical Engineering, international journal Food Engineering, ugc approved journals for engineering

Design and Implementation of All Optical Tunable Delay by the Combination of Wavelength Conversion and Fiber Dispersion

In this paper we have designed and implemented an all optical tunable delay element using the combination of wavelength conversion and fiber dispersion. We present wavelength conversion method that show with FWM. The characteristics of the proposed all optical based techniques for tunable delay element are discussed theoretically and demonstrated experimentally. This element operates near 1550nm and generates delay time range is 2430ps. 

by Pyae Phyo Swe | Tin Tin Ohn "Design and Implementation of All-Optical Tunable Delay by the Combination of Wavelength Conversion and Fiber Dispersion"

Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-5, August 2019,

URL: https://www.ijtsrd.com/papers/ijtsrd27874.pdf 

Paper URL: https://www.ijtsrd.com/engineering/electrical-engineering/27874/design-and-implementation-of-all-optical-tunable-delay-by-the-combination-of-wavelength-conversion-and-fiber-dispersion/pyae-phyo-swe

call for paper Manufacturing engineering, international journal Petroleum Engineering, ugc approved journals for engineering

Design and Implementation of Conveyor Belt Speed Control using PID for Industrial Applications

A conveyor system is a common piece of mechanical handling equipment that moves materials from one location to another. Many kinds of conveying systems are available, and are used according to the various needs of different industries. The purpose of this project is to improve the existing conveyor machine that located at the methodology lab in AL FALAH UNIVERSITY. This paper gives a review of the belt conveyor technology that focuses on the types of drives and the control system or the controller of the belt conveyor using PID controller. This paper highlights the characteristics, performance measure, requirements and the operational procedure of the belt conveyor drives and control systems. 

by Muhammad Shahid | Md Ghaysuddin "Design and Implementation of Conveyor Belt Speed Control using PID for Industrial Applications" 

Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-5 , August 2019,

URL: https://www.ijtsrd.com/papers/ijtsrd25294.pdf

Paper URL: https://www.ijtsrd.com/engineering/electrical-engineering/25294/design-and-implementation-of-conveyor-belt-speed-control-using-pid-for-industrial-applications/muhammad-shahid

call for paper Geological Engineering, international journal Gas Engineering, ugc approved journals for engineering

Study on Tall Structure for Hilly and Plane Surface under Seismic and Wind Load Conditions using STAAD ProV8i Software

There are various previous studies done for proper planning and good construction practices of multistoried buildings on sloping ground in particular, which lead to irregularities in plan and elevation of the buildings. Analysis and design of space building frame for seismic loading and wind pressure is very essential these days because of the construction of high rise buildings. It is also necessary to construct an economical and more durable structure. 

The current work examines the structural behavior of reinforced concrete columns, beam, and footing in sloping geometry. In this study a G 8 storey RCC building is analyzed on varying sloping angles i.e., 0o or plane surface and Hilly Surface 15o. The seismic forces and wind pressure are considered simultaneously as per IS 1893 2002 and IS 875 PART 3 respectively. The whole structure is analysis on software STAAD Pro v8i. The effect of Hilly ground on building performance during earthquake and wind pressure is observed. Seismic analysis has been done using Linear Static method. Analysis is done to evaluate the effect of sloping grounds on structural forces and displacement. In horizontal and vertical reaction, beam, shear force, and bending in lateral displacement in the column, axial force and columns, the moment of bending is critically analyzed to measure the effects of plane and hilly ground. It has been observed that the small height paving columns attract more forces, because their stiffness has increased significantly, which, in turn increases the bending moment and shear force. Thus, the section of these columns should be designed for modified forces due to the effect of hilly ground. 

by Akanksha Deshmukh | Pratiksha Malviya "Study on Tall Structure for Hilly and Plane Surface under Seismic & Wind Load Conditions using STAAD ProV8i Software" 

Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-5 , August 2019,

URL: https://www.ijtsrd.com/papers/ijtsrd25288.pdf

Paper URL: https://www.ijtsrd.com/engineering/civil-engineering/25288/study-on-tall-structure-for-hilly-and-plane-surface-under-seismic-and-wind-load-conditions-using-staad-prov8i-software/akanksha-deshmukh

call for paper Gas Engineering, international journal Geological Engineering, ugc approved journals for engineering

GSM Based Fire Security System

Telecommunication is a very important part of its life. This technology is used in a very sophisticated area like safety and security purpose. Using the GSM technology, telecommunication is conducive to save its life as well as households from fire accidents which have shown in this paper. In this paper, the overall circuit is constructed with six sections. The first section is power supply. The second section is temperature sensor and smoke sensor. The third section is Arduino. The fourth section is LCD display. The fifth section is fan, buzzer and water pump. The sixth section is GSM module. Temperature sensor is connected to the digital input pin of the Arduino and smoke sensor is connected to the analog input pin of the Arduino. When the temperature sensor detects heat and the smoke detector detects smoke the detectable measurement of smoke can be configured regarding the size and surroundings of the room, there is a LCD display which shows temperature and smoke data. When the temperature reach above 40°C and the smoke sensor had reached over 200ppm, the buzzer is ON, spray automatically water and send SMS. 

by Khin Thandar Tun | Aye Sandar Aung | May Lwin Thant "GSM Based Fire Security System"

Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-5, August 2019,

URL: https://www.ijtsrd.com/papers/ijtsrd26697.pdf 

Paper URL: https://www.ijtsrd.com/engineering/electronics-and-communication-engineering/26697/gsm-based-fire-security-system/khin-thandar-tun

call for paper Chassis Engineering, international journal Electrical Engineering, ugc approved journals for engineering

GSM Based Home Appliance Control System

In this paper, describes about how to control home appliances, auto door sliding motor, fan and lighting using GSM technology by using android application through android mobile phone. Performing of these tasks with a single android device makes every faster because the android makes SMS communication. This paper serve as a basic structure of the communication control system. The programming is done door operating system, hedge light bulbs and fan and light bulbs inside the home. Arduino Uno, Sensors and serial communicating devices are incorporated and synchronized with the personal computer. 

by Mrs Khin Ei Ei Khine | Mr Nay Soe Shwe | Mr Aung Myo Naing "GSM Based Home Appliance Control System"

Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-5, August 2019,

URL: https://www.ijtsrd.com/papers/ijtsrd26743.pdf 

Paper URL: https://www.ijtsrd.com/engineering/electrical-engineering/26743/gsm-based-home-appliance-control-system/mrs-khin-ei-ei-khine

call for paper Bio system Engineering, international journal Environment Engineering, ugc approved journals for engineering