Experimental Investigation on Replacement of Cement in Concrete Partially by using Dolamite Powder

Concrete is the most extremely used construction material within the world, which always uses natural resources like lime, aggregates and water. The production of cement in world has increased greatly, due to this cement production emission of CO2 gas has been increased tremendously, ultimately environmental pollution increased to very large extent. This affect to environment has been reduced by cement has been replaced by some supplementary materials like Dolamite Powder or Fly ash or GGBS and so on. 

Dolamite. Powder was conducted detailed study and lots of research work has been made on other waste materials and it is found there is a great future scope for research on Dolamite Powder as a replacement to cement, sand or both. Now in our case, cement has been replaced partially with in varying proportions likewise from 0 to 20 and its effect has been analysed on the standard consistency, soundness, setting times of cement and compressive strength of cement mortar mixes. The cubes and cylinders of concrete were casted for variable content of dolomite powder.

By Pramod Dhamne | Dr. P. B. Nagarnaik "Experimental Investigation on Replacement of Cement in Concrete Partially by using Dolamite Powder"

Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-3 , April 2019,

URL: https://www.ijtsrd.com/papers/ijtsrd23035.pdf

Paper URL: https://www.ijtsrd.com/engineering/civil-engineering/23035/experimental-investigation-on-replacement-of-cement-in-concrete-partially-by-using-dolamite-powder/pramod-dhamne

high impact factor, manuscript publication, paper publication for engineering

Parameter Estimation of Neutral Grounding Reactor for a Single Line to Ground Fault for Transformer

Single line to ground faults are the most prominent faults in the power system. This may damage the generators and transformers in the system ultimately leading to its failure. Introducing a neutral grounding reactor between the neutral and ground in the high voltage system, will reduce the fault current and hence will protect the power system components. . This paper will discuss the advantages, operation, application and selection of the neutral grounding reactor for transformer. 

By Snehal Pimpalkar | Mr. Mahesh Mankar "Parameter Estimation of Neutral Grounding Reactor for a Single Line to Ground Fault for Transformer"

Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-3 , April 2019,

URL: https://www.ijtsrd.com/papers/ijtsrd23030.pdf

Paper URL: https://www.ijtsrd.com/engineering/electrical-engineering/23030/parameter-estimation-of-neutral-grounding-reactor-for-a-single-line-to-ground-fault-for-transformer/snehal-pimpalkar

peer reviewed journals, international peer reviewed journal, high impact factor

Process Parameter Optimization for Resistance Spot Welding using Response Surface Methdology

Quality of product and process are mainly depends upon their process parameters and their levels selected for design and manufacturing. So, it is important to decide optimal levels of process parameters to get desired output variables. The study focuses on finding out optimal levels of process parameters in Resistance Spot Welding RSW and its effect on tensile strength and nugget diameter. The Response Surface Methodology RSM is employed for multi objective optimization of responses for maximizing tensile strength and minimizing nugget diameter. Response optimizer with desirability function is found for optimum results of response surface methodology. Analysis of variance ANOVA is carried out for analyzing contribution of each process parameter on the performance of RSW.

By Manjunath R. Rawal | Vaibhav Varane | Rakesh R. Kolhapure "Process Parameter Optimization for Resistance Spot Welding using Response Surface Methdology"

Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-3 , April 2019,

URL: https://www.ijtsrd.com/papers/ijtsrd23151.pdf

Paper URL: https://www.ijtsrd.com/engineering/mechanical-engineering/23151/process-parameter-optimization-for-resistance-spot-welding-using-response-surface-methdology/manjunath-r-rawal

technology journal, pharmacy journal, computer science journal

Design and Modeling of Pull Rod and Push Rod Suspension System

The main criterion of this project is to design a suspension system practically to a student formula vehicle and for systems, now loads are distributed to front and rear side. The stiffness of the spring is calculated by considering front and rear loads. The design of the spring, dash pot, rocker arms and push rod were done by LOTUS SHARK and modelling of these is done in SOLIDWORKS software. Later, the assembly of all parts and mono spring rocker arm front suspension system were designed racing cars. The dynamic loads are to be considered for the design of wheel assembly, frame, and transmission, steering and braking.

By Sateesh Kumar Revoor | Mittapally Nikhil | Jatothu Sucharitha | D. Anil "Design and Modeling of Pull Rod & Push Rod Suspension System"

Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-3 , April 2019,

URL: https://www.ijtsrd.com/papers/ijtsrd23263.pdf

Paper URL: https://www.ijtsrd.com/engineering/mechanical-engineering/23263/design-and-modeling-of-pull-rod-and-push-rod-suspension-system/sateesh-kumar-revoor

science journal, technology journal, pharmacy journal

Analysis of Air Conditioning Arrangement for Two Floor Shopping Complex by using Revit MEP Software

Heating, ventilation and air conditioning HVAC system provides thermal comfotness to occupants by supplying cooling air from air conditioning system through duct arrangement in building. The aim of this project is to analyse air conditioning arrangements for two floor shopping complexes using Revit MEP software. First and second floors layouts and ceiling with duct arrangements are created in software and then given positions like spacing and zonings to duct arrangements, finally by analysing the layouts individual cooling and heating loads are generated automatically. Compared to first floor second floor require more load.

By S. Visweswara Rao | Badisha Gopi | Aggidi Harish | Boda Sumanth "Analysis of Air Conditioning Arrangement for Two Floor Shopping Complex by using Revit MEP Software"

Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-3 , April 2019,

URL: https://www.ijtsrd.com/papers/ijtsrd23257.pdf

Paper URL: https://www.ijtsrd.com/engineering/mechanical-engineering/23257/analysis-of-air-conditioning-arrangement-for-two-floor-shopping-complex-by-using-revit-mep-software/s-visweswara-rao

journal publications, engineering journal, science journal

Warfare Robot

These robot used in military are usually employed with the integrated system, including video screens, sensors, gripper and cameras. Android application controlled WARFARE ROBOT, built in with Robotic arm mechanism to pick up or place small objects like explosives , an on board Wireless video camera, Infrared based surface depth and irregularities perception and android application for movement and other controls of the Robot. The robot will serve as an appropriate gadget for the defence sector to reduce the loss of human life.

by Sushmita Shivalkar | Geeta Yadav | Swapnali Patil | Sakshi Dale "Warfare Robot"

Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-3 , April 2019,

URL: https://www.ijtsrd.com/papers/ijtsrd22888.pdf

Paper URL: https://www.ijtsrd.com/engineering/electronics-and-communication-engineering/22888/warfare-robot/sushmita-shivalkar

multidisciplinary journal, peer reviewed journals, international peer reviewed journal

Risk Assessment in Manual Material Handling of an Edible Oil Company

The process of Shifting material manually has the potential for injury to employees. The purpose of this study is to assess and analyze the injury risk level in manual handling activity, as well as to improve the condition. The observed manual material handling activity is truck loading. This activity was analyzed using different software such as NIOSH equation, Rapid Entire Body Assessment, and compression force using 3DSSPP software as well as Nordic body map questionnaire was used to identify body discomfort level. In this study 5 male truck loading operators were taken as subjects, they are loading boxes from stacking area to truck manually. 

The task involved small repetitive movement while handling material, due to this the load man has faced work related musculoskeletal problems. The Nordic questionnaire is spread among the workers for collecting data, after collecting all information sorted out and analyzes the body parts using above software. The outcome shows that most of the workers who carry out activities have a high level of risk with the score of REBA exceeds points 12 risk is very high, need immediate changes required to improve the task , Literature survey indicates the lifting index should not be in more than 1, but the value obtained is 7.591 the job is more dangerous and stressful . 

Compression force exceeds the actual limit of 3400, but in this manual handling having compression force is 3408. When the Nordic body mapping method the major discomfort was found in the body parts such as Lower back, Forearm, upper arm. Based on the suggestion conveyor system is introduced and we re assess risk level of the body parts and the result shows that the risk level decreased up to 50 . Therefore replacing manual handling system with the conveyor system with reduces the lower back pain.

By Mohamed Ismail. S | Muthukumar. K "Risk Assessment in Manual Material Handling of an Edible Oil Company"

Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-3 , April 2019,

URL: https://www.ijtsrd.com/papers/ijtsrd23112.pdf

Paper URL: https://www.ijtsrd.com/engineering/mechanical-engineering/23112/risk-assessment-in-manual-material-handling-of-an-edible-oil-company/mohamed-ismail-s

special issue publication, multidisciplinary journal, peer reviewed journals